Tuesday, April 19, 2011

Rebuilding the floor

After the floor comes out, some of the glue and pressboard will remind attached to the joists.

In the middle is a section I removed with the Multi-Max scraper blade, but then learned it's easier to just chisel off the worst then sand with a sander.

I used my Bosch Random Orbital Sander.  It's readily available at Lowes and I think only around $60/$70 bucks and works pretty darn good.
I like how it has a wet vac port.

Then I sistered (attached) 2x6 to the out side wall floor frame, so the plywood flooring would have support along the edges.
Then spray foamed every crack. The black line down the middle is a metal frame strut and even though I replaced the outside joist bay with plywood (salvaged from different projects) there was still spaces where air leaked.

Then I added the insulation
I really like the JM Johns Manville from Lowes.  It has a plastic vapor retarder on one side and breathable material on the other sides.  NO PAPER food for mold!  It's very nice to work with. Hardly any iching after handling it, and the price isn't much different from the pink stuff.  Not enough to make me itch!!


This picture shows the uninsulated joist bay with the drain waste vent (dwv) pipes.  The black pipe on the left, is the original kitchen dwv.  I always had problems with the sink drain and after seeing how messed up the pitch was -no wonder. The white pvc pipe is my new washer dwv.
The 2 pipes on top of the insulation on the right is the kitchen water pipes. I insulated them, but now have decided to move my hot water heater and I removed them. The dvw joist bay was insulated before it was covered.

First sheet of flooring in! Yea! I decided to go with 3/4 osb tongue & groove. I would use plywood if I was building this to last 80 years, or if it was going to be exposed to the weather, but I used osb 15 years ago for my skirting around my crawlspace, painted it with exterior paint, and just ripped it out a few years ago and only the bottom half was rotted.






The section on the hallway side of the furnace was a trip!  The hole for the gas pipe was drilled through a joist because thats where the hole for the furnace hook-up was.  It had dropped almost an inch. To fix it
I placed a 2x6 perpendicular on edge, crossing 3 joists, wrapped a ratchet strap around both the broken joist and the perpendicular 2x6 and ratcheted the strap until the broken joist became level with the other joists.

Then I reinforced the broken joist with plywood and a few cross braces.
Sorry no pics, but was so involved I forgot...



All insulated!


And covered!

12 comments:

  1. Wow, looks good. I myself live in a mobile home that needs remodeling. I'm a female and am just curious.. How did you learn to do all this stuff? I want to learn as well because I can't afford to hire someone to do what needs to be done. Are there books that you've learned from? Thanks for what you have shared

    ReplyDelete
    Replies
    1. Hi Naomi, I guess most of my education came from watching This Old House (since it began in the 70's), HGTV & DIY Network... And tons of research on the internet. You Tube has many videos on mobile Home repairs. It is a dirty yucky job, and it took several years of christmas presents asking for tools to acquire most my tools, but if you are like me and are determined to get it done, my two best pieces of advice are "Always work from the general to the specific." J. Raabe from countryplans.com and if you think you can, or you think you can't, your right! Good luck and just remember, what ever you think it will cost, triple it! Helen

      Delete
    2. I have remodeled my 1972 DBL wide not knowing about how to do anything from the get go.
      It's true YouTube is great! That was my go to (and lots of prayer of course).
      I have been remolding for about four years on a half shoestring budget.
      I have learned how to re-wire, re-plumb, re-build floors, ceilings and walls, and I am very thankful for all of it!
      Truth is " what ever you think it will cost, triple it! " Is correct!
      I wish I could post some pics for you.
      However you CAN do anything you set your mind to (of course with the right tools)!
      All the best to you!

      Delete
  2. Great post! Thanks for sharing such a awesome information. I must say very good job.
    Approved ny rising contractors

    ReplyDelete
  3. Thanks for sharing about Favorable Financing Costs Not Impacting Remodeling Activity During Recovery

    GreenWorks Construction Design Inc

    ReplyDelete
  4. My house needs this so bad.. living with three kids I recently bought a older mobile home that they trashed but I have remodeled here and threre,, I need a Complete makeover from floor to ceiing.. I am just trying to do one room one issue at a time... its sooo slow.. also my income is short so it lags work. I just wish I had energy to do this... Great job.

    ReplyDelete
  5. Very informative, good job guys and thanks for sharing such a awesome blog. home contractors

    ReplyDelete
  6. Nice and very informative tips and guidelines about rebuilding the floor. Thanks for sharing it. You can also try the reliable contractor in Pittsburgh, John Hancock Contracting Inc.

    ReplyDelete
  7. I appreciate everything you have added to my knowledge base.Admiring the time and effort you put into your blog and detailed information you offer.Thanks. Remodeling Pearland TX

    ReplyDelete
  8. Интересуетесь, где заказать оконные блоки и двери из дерева? Можем посоветовать компанию СВ Окна, существующую уже более 25 лет. Группа компаний производит широкий диапазон деревянных стеклопакетов от эконом до люксовых. Даже самый прихотливый клиент найдет подходящие деревянные окна. В программе производства присутствуют недорогие деревянные окна из соснового бруса, деревянные евроокна, дерево-алюминиевые окна, двери-порталы, двери-гармошки.

    ReplyDelete
  9. You have done a great job. I will definitely dig it and personally recommend to my friends. I am confident they will be benefited from this site remodel corpus christi

    ReplyDelete